Digital-alert-systems DASDEC-II QUICK START UP GUIDE Manuel d'utilisateur

Digital Alert Systems A division of Monroe Electronics 585-765-1155 | fax 585-765-9330 100 Housel Ave. | Lyndonville | NY | 14098 www.digitalalertsys

Quick Start Guide for Your DASDEC II Page 10 of 40 Using 4 External Inputs 1. Use the following connections: Then from the Setup

Quick Start Guide for Your DASDEC II Page 11 of 40 Using 3 Internal radios and a 4th External input 1. Use the following connections:

Quick Start Guide for Your DASDEC II Page 12 of 40 Using EAS Monitoring Expansion (Auxiliary 2) Inputs 1. Use the following connections:

Quick Start Guide for Your DASDEC II Page 13 of 40 MPEG Encoder If you have purchased the DVS-168 or DVS-644 options see section 4.10.1 and

Quick Start Guide for Your DASDEC II Page 14 of 40 2) After logging in Click on the “Setup” tab (circled in red), then click on the “Audio”

Quick Start Guide for Your DASDEC II Page 15 of 40 3) With the antenna lines connected to the DASDEC-II adjust the internal tuners for your

Quick Start Guide for Your DASDEC II Page 16 of 40 On the Alert Decoding Audio Configuration page, scroll down to the Main Audio heading. S

Quick Start Guide for Your DASDEC II Page 17 of 40 8) The DASDEC-II will now monitor your assigned and enabled decoders for encoded EAS me

Quick Start Guide for Your DASDEC II Page 18 of 40 Step 4 – Setting the Time **NOTE**: The following steps are written for a DASDEC that ha

Quick Start Guide for Your DASDEC II Page 19 of 40 3) On the “Setup > Time” page set your time zone (circled in red) and then click the

Quick Start Guide for Your DASDEC II Page 2 of 40 Table of Contents Step 1 – Setting the IP Address ...

Quick Start Guide for Your DASDEC II Page 20 of 40 Step 5 – Changing the Default Admin Password After setting the IP Address of the DASDEC-I

Quick Start Guide for Your DASDEC II Page 21 of 40 4) Towards the bottom of the left hand column are the fields used to change the password

Quick Start Guide for Your DASDEC II Page 22 of 40 Step 6 – Alert Decoding, Filtering & Forwarding By default the DASDEC-II monitors for

Quick Start Guide for Your DASDEC II Page 23 of 40 4) The drop-down box is used to set how long non-national alerts, such as Required Mont

Quick Start Guide for Your DASDEC II Page 24 of 40 7) With “Auto-Forward Mode” your station can be operated in auto or manual mode. The se

Quick Start Guide for Your DASDEC II Page 25 of 40 9) The settings under the heading Configure Duplicate Alert Handling for Decoder Auto-Fo

Quick Start Guide for Your DASDEC II Page 26 of 40 12) The final part of configuring alert forwarding is to set your areas FIPS codes. B

Quick Start Guide for Your DASDEC II Page 27 of 40 Step 7 – Alert Encoding and Originating Before the DASDEC-II can be used to originate ale

Quick Start Guide for Your DASDEC II Page 28 of 40 3) Use the drop-down menu under the heading Non-national alert play scheduling to contr

Quick Start Guide for Your DASDEC II Page 29 of 40 6) Finally, the section Configure Available FIPS for Encoder Alert Origination is where

Quick Start Guide for Your DASDEC II Page 3 of 40 Please Register Your DASDEC II To verify that you have the latest version of software in

Quick Start Guide for Your DASDEC II Page 30 of 40 Step 8 – Set-up Station Interface and Required Tests After the DASDEC-II’s Base Station c

Quick Start Guide for Your DASDEC II Page 31 of 40 4) Next the “Forwarding Station ID” must be changed, click on the link in the red box t

Quick Start Guide for Your DASDEC II Page 32 of 40 7) By default, new Station Configurations will have the station operate in Manual Forwa

Quick Start Guide for Your DASDEC II Page 33 of 40 9) Next, program the FIPS codes the DASDEC-II will send on that stations interface for

Quick Start Guide for Your DASDEC II Page 34 of 40 12) On the Alert Encoding Audio Configuration page you must click on the check box (circ

Quick Start Guide for Your DASDEC II Page 35 of 40 Step 9 – GPIO Configuration The DASDEC-II ships with two General Purpose Inputs and two

Quick Start Guide for Your DASDEC II Page 36 of 40 3) The GPIO Setup screen has a table at the top which will show what the current progra

Quick Start Guide for Your DASDEC II Page 37 of 40 5) For further information on how the other GPIO in and out setting operate refer to th

Quick Start Guide for Your DASDEC II Page 38 of 40 Step 10 – E-Mail Setup The DASDEC-II has the ability to send e-mails when Alerts are sent

Quick Start Guide for Your DASDEC II Page 39 of 40 3) In the field next to Outgoing Email Server Name (circled in red) enter the IP address

Quick Start Guide for Your DASDEC II Page 4 of 40 Quick Start Guide for Your DASDEC-II The official Digital Alert Systems manual for your EA

Quick Start Guide for Your DASDEC II Page 40 of 40 7) The DASDEC-II will send EAS Event Reports to whatever e-mail address you enter into

Quick Start Guide for Your DASDEC II Page 5 of 40 Your DASDEC-II shipped with a CAT-5 network Crossover cable; this cable allows you to conn

Quick Start Guide for Your DASDEC II Page 6 of 40 to the DASDEC-II’s login page. Enter the default user name “Admin” and default password “d

Quick Start Guide for Your DASDEC II Page 7 of 40 Gateway in the field provided (Circled in green). Finally click “Accept Changes/Restart Ne

Quick Start Guide for Your DASDEC II Page 8 of 40 12) The IP Address is now set. All further programming will be accessed through the DASD

Quick Start Guide for Your DASDEC II Page 9 of 40 Using 2 Internal radios and 2 External inputs 1. Use the following connections: